12-05-31 | Stage One & A Case.
2 posts
• Page 1 of 1
12-05-31 | Stage One & A Case.
by FishPi » Thu May 31, 2012 9:00 pm
I have all the parts needed for stage one of the build.
The hull.
The motor & gearbox.
Kort nozzle.
Kort propeller.
Propshaft
Couplings.
Rudder servo.
The Jubilee week will mark the beginning of the build. I have a work free 7 days put aside to work on the FishPi
But first. There was a post on the Raspberry Pi News feed (http://www.raspberrypi.org/archives/1310) which showed a paper case for the RPi called the Punnet. Being somewhat of a fan of papercraft I decided to give it a go.....
The instructions say to use foam for the 2mm spacer, but I didn't have any, so I used cardboard instead. I glued the template straight onto the cardboard and left it to dry before cutting it out.
I left the AV & Audio sockets unopened as I wanted to check the alignment before cutting.
Aligning the AV & Audio sockets. I have also cut out an extra window next to the USB sockets so I can get a good look at the LEDs to check the RPi's status.
The Punnet alongside papercraft models of the Audi S1, Lancia Stratos & McLaren M8. The models are available for download from http://www.ymjr.cz.
The lights are clearly visible through the added viewing window. The Punnet is still in alpha and I look forward to making future models. The Punnet was laser printed onto 300gsm white paper, it cost 36 Pence.
The hull.
The motor & gearbox.
Kort nozzle.
Kort propeller.
Propshaft
Couplings.
Rudder servo.
The Jubilee week will mark the beginning of the build. I have a work free 7 days put aside to work on the FishPi
But first. There was a post on the Raspberry Pi News feed (http://www.raspberrypi.org/archives/1310) which showed a paper case for the RPi called the Punnet. Being somewhat of a fan of papercraft I decided to give it a go.....
The instructions say to use foam for the 2mm spacer, but I didn't have any, so I used cardboard instead. I glued the template straight onto the cardboard and left it to dry before cutting it out.
I left the AV & Audio sockets unopened as I wanted to check the alignment before cutting.
Aligning the AV & Audio sockets. I have also cut out an extra window next to the USB sockets so I can get a good look at the LEDs to check the RPi's status.
The Punnet alongside papercraft models of the Audi S1, Lancia Stratos & McLaren M8. The models are available for download from http://www.ymjr.cz.
The lights are clearly visible through the added viewing window. The Punnet is still in alpha and I look forward to making future models. The Punnet was laser printed onto 300gsm white paper, it cost 36 Pence.
FishPi: An autonomous drop In the Ocean.
-
FishPi - Site Admin
- Posts: 389
- Joined: Tue Mar 06, 2012 9:02 pm
Re: 12-05-31 | Stage One & A Case.
by protter » Fri May 10, 2013 12:00 am
The Punnet alongside papercraft models of the Audi S1, Lancia Stratos & McLaren M8. The models are available for download from http://www.ymjr.cz.
Man I love this site, great job! Thanks for sharing the Audi and McLaren model links
Peter
- protter
- Posts: 3
- Joined: Thu May 09, 2013 11:49 pm
2 posts
• Page 1 of 1
Return to The Proof-Of-Concept Vehicle (POCV)
Who is online
Users browsing this forum: No registered users and 1 guest
